Press the front cover release button and then open the front cover. If you put the cartridge in properly, the blue locklever will lift automatically. These parts would affect the product quality greatly if they lost their function even if they do not appear to be damaged or there is no change in their appearance.
The periodical replacement parts listed below should be replaced at the service center referring to the service life. Air duct Filter Hooks Sub duct Fig.
Slide the Air duct to the direction of 29b and remove the Air duct. Laser unit Hook Hook Air duct Fig. NOTE: After disconnecting flat cable s , check that each cable is not damaged at its end or short-circuited. Air duct Filter Fig. CAUTION: To prevent the deformation of the pressure roller, the fuser unit spare part is shipped with its pressure roller at low nip pressure.
Taptite, bind B M4x16 Fuser unit Fig. FU harness cover 2 Hook Fig. Paper tray Fig. Printer AC cord Fig. When you replace the toner cartridge or the drum unit, make sure you clean the inside of the printer. If printed pages are stained with toner, clean the inside of the printer with a dry soft cloth.
Wait for the printer to cool down before you touch the internal parts of the printer. If you have print quality problems, clean the corona wire as follows: 1 Press the front cover release button and then open the front cover. NOTE: The following troubleshooting sections contain both the actions which users should take or check and the ones which service technicians should perform. Identify the error from the table below and take the corrective action described for each indication to correct it.
Front cover is open Close the front cover of the printer. Fuser cover is open Close the back cover of the printer. Dust on drum The corona wire needs to be cleaned. The printer automatically recovers from most errors.
If not, the error is cleared by holding down the Go button on the control panel. Page Service Calls Service Calls 2. Type of service call Type of service call Instruct the user to turn off the power switch, wait 5 seconds and then turn it on again. If the error is not cleared and the same service call appears, identify the error from the table on the next page and take the corrective action described for each indication to correct it.
If still remains, replace the main PCB. Refer to 3. Cancel the print job if you want to delete the data remaining in the printer. Take the corrective actions for the error message. Clear the jammed paper if there is any inside the drum unit.
If you put the cartridge in properly, the blue lock lever will lift automatically. One of the following LCD messages will appear to tell you where to find the jammed paper. While pressing the blue paper-guide release lever, slide the paper guides to fit the paper size. Make sure that the guides are firmly in the slots. The jammed paper will be pulled out with the drum unit and toner cartridge ASSY. When you open the front cover or back cover of the printer, DO NOT touch the shaded parts shown in the illustrations.
When a paper jam occurs inside the printer, you have to find the location of the paper jam first, remove the jammed paper and then take the appropriate countermeasure referring to the table below; Even if the same problem occurs again, follow the procedures in the table below.
Both high temperature and humidity will cause paper to curl. Turn over the stack of paper in the paper tray. User Check 1 Check that the printer cable is not damaged or broken. Check also that the cable is connected to the correct interface connectors of both the printer and PC. High-voltage Check the connections of the Replace the high-voltage power supply connector between the high Page Replace the main PCB.
Remove the cause of non- not move smooth operation of the link Isn't the link lever bent? Even if the same image defect appears, the following procedures should be followed in the event of specific image defects. High temperature and high humidity conditions can increase the amount of background shading. Drum unit Are the drum shaft and drum Install a new drum unit.
Clean the corona wire with the wire cleaner. Install a new toner cartridge. High temperature and high humidity conditions can cause this problem. Print paper Nip release Does the position of the nip Return the nip release levers to lever release levers in the fuser unit the original position. Check if there is any play. Scanner LD Is the laser diode or the Replace the laser unit.
Corona dirty Is the corona wire dirty? Drum Is the contact between the Clean contact connection drum unit and printer body A rough surfaced paper may cause the problem. P-1 The printer prints unexpectedly or it prints garbage data. User Check 1 Check if the printer cable is not too long. User Check 1 Press the Go button on the control panel to print the data remaining in the printer. Page Network Problem Check the following: 1.
Make sure that it is completely inserted into the printer. Lift up the support flap to prevent paper from sliding off the face-down output tray, or remove each page as soon as it comes out of the printer. Page 20 MP Tray mode is automatically turned on when paper is put in the multi-purpose tray.
For the proper paper to use, see About paper on page 5. Page 21 Open the MP tray and lower it gently. Pull out the MP tray support flap 1. Printing Methods Page 22 While pressing the paper-guide release lever, slide the paper guide to fit the paper size. Send the print data to the printer. For more information on the envelope size, see Paper size on page A Page 24 Open the MP tray and lower it gently.
While pressing the paper-guide release lever, slide the paper guide to fit the paper size. Stacking the sheets or envelopes may cause the paper to jam or curl.
Put a new DL size double-flap envelope in the MP tray with the longest edge of the envelope in first, then print again. Page Duplex Printing Use plain paper or recycled paper. Do not use bond paper. Manual duplex printing from the paper tray In the printer driver choose the Advanced tab, then choose the Manual Duplex printing mode, and from the Basic tab choose the Paper Source to be Tray1.
Next, put the printed pages in the tray, with the printed side face up. If you print 10 pages on 5 sheets of paper, it will print page 2 and then page 1 on the first sheet of paper. It will print page 4 and then page 3 on the second sheet of paper. It will print page 6 and then page 5 on the third sheet of paper, and so on.
The printer will print on both sides of the paper automatically. Open the Properties dialog box in the printer driver. From the General tab, choose the Printing Preferences icon. Page Driver And Software Driver and Software Printer driver A printer driver is software that translates data from the format used by a computer to the format that a particular printer needs.
Typically, this format is page description language PDL. Print Setting You can manually change the print setting. Page Device Options Device Options You can set the following in Printer Function: You can jump to the page for each Printer Function by choosing the function name in the list below. Page 38 5 minutes. Intelligent Sleep Mode automatically adjusts to the most suitable timeout setting depending on the frequency of your printer use. While the printer is in sleep mode, all the LEDs are off, but the printer can still receive data.
Receiving a print file or document or pressing Go will automatically wake up the printer to start printing. The page protection feature allows the printer to create the full-page image to be printed in memory before physically moving the paper through the printer.
Use this function when the image is complicated and the printer has to wait to process the image before printing. Page Accessories Tab The Auto Detect function finds the currently installed optional unit devices and shows the available settings in the printer driver. When you click Auto Detect, options that are installed on the printer will be listed. You can manually add or remove options. Page Support Tab Print Settings 4 This will print the pages that show how the internal settings of the printer have been configured.
Print Fonts 5 This will print the pages that show all the internal fonts of the printer. Device Settings tab Choose the options you have installed. Page 43 3. Set the Scaling and TrueType Font settings 2. You can change settings by choosing the setting in the Printer Features list 3 : Print Quality Media Type Toner Save You can save running costs by turning on the Toner Save, which reduces the print density.
Page 47 When the printer does not receive data for a certain period of time timeout , it enters sleep mode. In sleep mode, the printer acts as though it were turned off. The default timeout is 5 minutes. Page Uninstalling The Printer Driver You can uninstall the printer driver that you installed with the following steps.
Run the Printer Setup Utility printer you want to remove and remove it by clicking the Delete button. Page Software Then, each user just clicks that file to have the printer driver, port driver, IP address, and so on, automatically copied to their PC. Page About Emulation Modes Professional, Some applications support these dot matrix printer emulations.
Page Automatic Interface Selection Automatic interface selection This printer has an automatic interface selection feature that is turned on by default. When you use the parallel interface, you can turn the high-speed and bi-directional parallel communications on or off by using Remote Printer Console. Note When the power switch is off or the printer is in sleep mode, all the LEDs are off.
LED is off. LED is on. Page 54 4. Control Panel Printer status Sleep mode The power switch is off or the printer is in sleep mode. Pressing Go wakes up the printer from sleep mode to ready mode. Ready to print The printer is ready to print. Page 55 4. Control Panel Printer status Data remaining in memory There is remaining print data in the printer memory. If the yellow Status LED is on for a long time and nothing has printed, press Go to print the remaining data in memory.
Page 56 9 or Printing on thick paper, labels and envelopes on page Paper jam Clear the paper jam. See Paper jams and how to clear them on page If the printer does not start printing, press Go. Page Service Call Indications Status If this error occurs, turn off the printer power switch, wait a few seconds, and then turn it on again. Leave the printer for 10 minutes with the power on. If the error occurs again, call your dealer or Brother authorized service representative.
Page 58 4. Make a note of the indication and report the error status to your dealer or a Brother authorized service representative by referring to the above table. Note Make sure that the front cover is completely closed before you report a service call.
Error recovery If there is an error, the printer will recover automatically from some errors. If an error is not automatically cleared, press Go to clear the error, and then continue to use the printer.
Using control panel button Turn off the printer. Make sure that the front cover is closed and the power cord is plugged in. Turn on the printer and wait until the printer is in the ready state. Press Go three times within 2 seconds. The printer will print the current printer settings page. Page Print Fonts Print Fonts You can print a list of the internal fonts using the control panel button or printer driver. Using the control panel button Turn off the printer.
Page Network Default Setting For HlDn If you want to reset the print server back to its default settings resetting all information such as the password and IP address information , follow these steps: Turn off the printer. When both optional trays are installed, the printer can hold up to sheets of plain paper. If you want to buy an optional lower tray unit, call the dealer you bought the printer from. Reconnect the interface cable to your printer.
Plug the printer back in, and then turn on the power switch. Note To make sure that you have installed the DIMM properly, you can print the printer settings page that shows the current memory size. When you open the front cover or back cover of the printer, DO NOT touch the shaded parts shown in the illustration. If the LED shows this message, the printer has nearly run out of toner. Buy a new toner cartridge and have it ready before you get a Toner Life End message.
To replace the toner cartridge, see Replacing the toner cartridge on page Safety Precautions What is in the box? Control panel Printer LED Indications Install the drum unit and toner cartridge assembly Load paper in the paper tray Print a test page For parallel interface cable users For shared network printer users For USB interface cable users Web browser Network default settings Print the Printer Settings Page Shipment of the printer There are high voltage electrodes inside the printer.
Before you clean the inside of the printer, make sure that you have turned off the power switch and unplugged the printer from the AC power outlet. DO NOT handle the plug with wet hands. Doing this might cause an electrical shock. After you have just used the printer, some internal parts of the printer will be extremely hot. DO NOT touch the shaded parts shown in the illustration when you open the front or back cover of the printer.
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to ignite inside the vacuum cleaner, potentially starting a fire.
Please carefully clean the toner dust with a dry, lint-free cloth and dispose of it according to local regulations. DO NOT use flammable substances near the printer. Doing this might cause a fire or electrical shock. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. A shielded interface cable should be used in order to ensure compliance with the limits for a Class B digital device. Changes or modifications not expressly approved by Brother Industries, Ltd.
Before you use this product, make sure that you use one of the following interface cables. This printer is certified as a Class 1 laser product under the U. This means that the printer does not produce hazardous laser radiation. Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation. The U.
0コメント